Skip to content

2008 Toyota Yaris Rear Bumper Removal

Assuming you would like a step-by-step guide on how to remove the rear bumper on a 2008 Toyota Yaris: The first thing you will need to do is open the trunk and locate the two bolts at the top of the bumper. Once you have found these, use a socket wrench to remove them.

Next, you will need to find the three bolts that are located under the car. Two of these bolts will be near the wheels and one will be in the center of the bumper. Again, use a socket wrench to remove these bolts.

Now that all of the bolts have been removed, you should be able to gently pull the bumper off of the car.

Removing the rear bumper on a 2008 Toyota Yaris is a simple process that can be completed in about an hour. The first step is to remove the two bolts that secure the bumper to the body of the car. These are located at the top of the bumper, just behind the taillights.

Once these bolts are removed, the bumper can be pulled away from the car. There are two plastic clips holding the wiring harness for the taillights in place. These need to be removed before proceeding.

With these clips removed, gently pull on the wiring harness and it will come free from its mounting location. Now, there are four bolts holding the bumper onto the frame of the car. Two of these bolts are located at each side near where the taillights mount.

Remove these bolts and then lift up on the rear of the bumper to remove it fromthe car.

2008 Toyota Yaris Rear Bumper Removal

Credit: modeautoconcepts.com

How Do I Remove the Rear Bumper on My 2008 Toyota Yaris

If you need to remove the rear bumper on your 2008 Toyota Yaris, there are a few things you need to know. First, you will need to remove the two bolts that hold the bumper on. These are located on the bottom of the bumper.

Next, you will need to remove the four screws that hold the bumper cover in place. Once these are removed, you can pull the bumper off of the car.

See also  Toyota Yaris Locked Steering Wheel

What Tools Do I Need to Remove the Rear Bumper on My 2008 Toyota Yaris

Assuming you would like a blog post discussing the tools necessary to remove a rear bumper on a 2008 Toyota Yaris: In order to remove the rear bumper on your 2008 Toyota Yaris, you will need: – A socket wrench set

– A screwdriver – A ratchet and extension cords – A pry bar (optional)

First, begin by loosening the bolts that hold the bumper in place with your socket wrench. There should be four bolts in total. Once these are loose, disconnect the wiring harnesses that are attached to the back of the bumper.

You may need a screwdriver for this step. Next, use your ratchet and extension cords to remove the two bolts that secure the bumper brackets to the frame of your car. With all hardware removed, the final step is to simply pull off the rear bumper.

If it is stuck or difficult to remove, you can try using a pry bar to loosen it up before pulling. And that’s it! With these steps completed, you have now successfully removed the rear bumper from your 2008 Toyota Yaris.

How Do I Reinstall the Rear Bumper on My 2008 Toyota Yaris

Assuming you are referring to the plastic/fiberglass bumper: The first step is to remove the old bumper. To do this, you will need to remove the bolts that hold it in place.

There are generally two bolts on each side near the top of the bumper, and two more in the middle at the bottom. Once these are removed, the bumper should come right off.

See also  Toyota Corolla Horn Upgrade
Next, clean up any dirt or debris on the car where the new bumper will be mounted.

This will help ensure a good bond between the car and the new bumper. To install the new bumper, line it up with the holes where the old one was mounted and start threading in the bolts. Once all four bolts are tight, give them an extra quarter turn with a wrench to make sure they’re secure.

And that’s it! Your new rear bumper is now installed.

Toyota Yaris 2005-2013 rear bumper removal

Toyota Yaris Rear Bumper Replacement Cost

Toyota Yaris Rear Bumper Replacement Cost If you’re in need of a Toyota Yaris rear bumper replacement, there’s no need to worry. This is a relatively inexpensive repair that won’t break the bank.

In most cases, you can expect to pay between $200 and $300 for the parts and labor involved in this repair. However, if you have a more expensive model of Toyota Yaris, the cost could be closer to $400. When it comes to replacing the rear bumper on your Toyota Yaris, there are a few things to keep in mind.

First, you’ll need to decide whether you want to replace the entire bumper or just the cover. If you choose to replace the entire bumper, it will be more expensive but it will also give your car a fresh look. Replacing just the cover is less expensive and will still get the job done.

Next, you’ll need to decide what kind of material you want your new rear bumper to be made out of. There are three main choices: plastic, fiberglass or carbon fiber. Plastic is by far the most affordable option but it doesn’t offer as much protection as either fiberglass or carbon fiber.

Fiberglass is more durable than plastic but not as strong as carbon fiber; however, it’s usually less expensive than carbon fiber bumpers. Carbon fiber offers superior strength and durability but comes with a higher price tag. Ultimately, the choice is yours and should be based on your budget and personal preferences.

See also  Toyota Airbag Light on No Codes


Once you’ve decided on which type of bumper material you want, it’s time to start shopping around for prices. The best way to do this is by visiting your local auto body shop or searching online for “Toyota Yaris rear bumper replacement cost.” You can also call around to different shops and ask for quotes over the phone before making your final decision.

By doing your research ahead of time, you can be sure that you’re getting the best possible deal on your Toyota Yaris rear bumper replacement cost!

Conclusion

The 2008 Toyota Yaris rear bumper is easy to remove. First, disconnect the negative battery terminal to avoid any electrical shorts. Next, remove the two bolts that hold the bumper on at the top of the wheel well.

These are 10mm bolts. Finally, pull the bumper off starting at the top and working your way down. Be careful not to damage the paintwork as you remove the bumper.

Leave a Reply

Your email address will not be published. Required fields are marked *