Skip to content

2015 Toyota Yaris Third Brake Light Replacement

To replace the third brake light on a 2015 Toyota Yaris, first remove the two screws that secure the light to the trunk lid. Next, disconnect the electrical connector from the back of the light. Finally, remove the old bulb and insert a new one.

If your 2015 Toyota Yaris is in need of a new third brake light, don’t fret – replacing it is a quick and easy process! Here’s what you’ll need to do: 1. Pop the trunk open and locate the third brake light assembly.

It will be mounted on the inside of the trunk lid, towards the top. 2. Use a Phillips head screwdriver to remove the two screws that secure the assembly in place. 3. Carefully disconnect the wiring harness from the back of the assembly.

4. Pull out the old assembly and insert the new one in its place. Reconnect the wiring harness and screw everything back into place. And that’s it!

Your Yaris will now have a brand new, functioning third brake light – keeping you safe on those dark roads ahead.

2015 Toyota Yaris Third Brake Light Replacement

Credit: www.amazon.com

How Do You Change the Third Brake Light?

When it comes to replacing a brake light, the third brake light is no different than the other two. The only exception is that on some vehicles, the third brake light may be integrated into the rear window instead of being its own separate component. Regardless, the process for changing a brake light is generally the same across all vehicle makes and models.

Assuming your third brake light is a separate component, begin by opening up the trunk or hatch of your vehicle. Locate the screws or fasteners holding the lens in place and remove them. With the lens removed, you should now have access to the bulb socket.

Unscrew or unclip any retaining devices and carefully pull out the old bulb. Be careful not to touch the glass portion of the new bulb with your fingers as this can cause premature failure. Install the new bulb in reverse order and test to make sure it’s working before reassembling everything.

See also  Toyota Rav4 Ac Light Blinking

Where is the 3Rd Brake Light Located?

The third brake light is located in the center of the rear window, just above the level of the trunk lid. It is typically a round or oval-shaped light, and may be red, amber, or clear in color. This light is required by law on all passenger vehicles in the United States.

How Do You Change a Yaris Bulb?

If you need to change a headlight, brake light, turn signal or other bulb on your Toyota Yaris, follow these instructions. Replacing a headlight is simple and can be done in just a few minutes. To change a headlight bulb on your Toyota Yaris:

1. Open the hood and locate the headlight assembly. 2. Unplug the electrical connector from the back of the headlight assembly. 3. Remove the retaining clip that secures the bulb in place.

4. Pull out the old bulb and insert a new one into the socket. Make sure it is properly seated before replacing the retaining clip and reconnecting the electrical connector.

How Do You Change a Third Brake Light on a Toyota Corolla?

Assuming you need to replace the entire light: 1. Open your trunk and locate the two screws that are holding the brake light in place. 2. Unscrew these screws with a Phillips head screwdriver and pull the entire light assembly out of the car.

3. Take your new brake light and insert it into the opening, screwing in the two screws until they are tight. 4. Close your trunk and test your brake light to make sure it is working properly.

See also  Difference between Gt And Gts

how to change High level brake Light | Right Brake Light on Toyota Yaris | part 1 #taillight

Toyota Yaris Led Brake Light

Most cars on the road today have LED brake lights. So, it’s no surprise that the Toyota Yaris is equipped with LED brake lights. LED brake lights are brighter than traditional incandescent bulbs and they light up faster, too.

That means that drivers behind you will have more time to react when you hit the brakes. And, since LEDs use less energy than incandescent bulbs, your car’s battery will thank you for making the switch to LEDs.

Conclusion

If your 2015 Toyota Yaris is in need of a new third brake light, follow these easy steps to replace it yourself. You’ll first need to remove the old light by unscrewing the two screws that hold it in place. Next, disconnect the electrical connector and pull the light out.

To install the new light, simply reverse these steps. Be sure to test the new light before putting everything back together to ensure it’s working properly. With just a few simple tools and a bit of time, you can have your Yaris’ third brake light replaced in no time!

Leave a Reply

Your email address will not be published. Required fields are marked *